Leaderboard

Damn... I've been Found. Sorry Dave, I won't do it again... I teletransported myself to daves loft, with the intention of switching off the alarm from that socket (I failed) and then clean the house of electronic goodies and and garage stuff... planning to go back home driving the Mega S2000 with the wrong front wings... When I was investigating why the alarm was still on after switching that socket off... I saw an squirrel, with a few more squirrels on its back, dancing some sort of evil dance that scared the hell out of me, and decieded that wasn't worth the trouble... so I teletransported myself back to Crewe. Hope this clarifies all. Dave's house is not haunted. buy with confidence.

Now sold

i'll take delivery of that Porsche for you then!

No, Seriously, they are wrong. I wouldn't mind the car anyway...

You should ban that bear grills fella from yer loft , up to no good ill be bound

Dont trust 'em , sounds like a con to me . If you Email me your bank details I can check it out and make sure everythings kosher

Only bit I understood of that post was "£120"

Just read this whole build thread today, absolutely unreal. Seriously talented guy top job Mark

Looks dead easy, Dave. There are pre-made mounting brackets for the steppers and very cheap Arduino shields for the stepper motor drivers. Add an NVR switch, an old laptop power supply and a PC fan - then it's ready to go. The Arduino code is available and just loaded, with a free G-Code sender software for the laptop. I've hooked up one motor and it seems to be working... Total conversion cost about £120

I've done one of those too, a bit scruffy but satisfying. I've always wanted one so had to make it. It's from a 50mm cube. The black marks are because I hadn't finished cleaning it before I took the pic.

heres why I wouldn’t want the chocolate roll bar!

Ok folks a week to go see you all there

I've had one of those for a few years now and it's very useful. It's great for aluminium or brass, steel needs more care and very small cuts. As a novelty I made the item in the pictures for fun.

Closest thing to hand

**NOW SOLD** For sale: 1992 Westfield SEIW 2.0 Pinto Kent FR32 cam Type 9 5speed gearbox Twin Weber DCOE40 carbs M16 front calipers mintex 1144 pads Roughly about 24,000 miles( It had a digital bike speedo on when i bought it) MOT'd until 9/6/2019 The engine was rebuild by the previous owner. 205 block, unleaded head. Detachable steering wheel. The car had a new alternator, starter motor, cambelt with tensioner, clutch cable, front calipers, discs, pads, rear discs, pads, electronic ignition, coil,electronic VDO speedo with sender , water temp gauge and facet electric fuel pump last August before I drove it down to Monza to watch F1 then up to Germany to take it around the Nurburgring. Did a total of 2600 miles and only the throttle cable snapped which was repaired at the side of the road in Switzerland(a replacement will be included but the original is still going). The carbs will need rebalancing at some point, it was done last year before the road trip. Also retrimmed the dash and replaced the warning lights with black facia LED ones. It's got an FIA kill switch wired in, 12V and 2 usb sockets in the dash too. Fibreglass seats that were red so I retrimmed them in black faux alcantara which is on the top of the dash as well, they are a bit wrinkled near the base but are the widest seats i've tried being tall and not slim I kept them. New Luke harnesses fitted. I fitted a new heater in the car with windscreen and lower vents as when I bought the car it had an Aero screen on it. Retrimmed the interior carpet along with a bit of sound proofing material. The bootbox has been cut at the sides as it must of had an RAC roll bar at some point. I've got a replacement one that will be included but its in orange. It will also come with a set of 195/50/15 and 205/50/15 toyo 888 tyres which I removed when I bought it to fit road tyres on. The 205 rears were new on and still have the colour markings on them. It's on Toyo T1R's at the moment. Will also come with 2 new front Westfield fake carbon cycle wings which i never got around to fitting. Just fitted LED headlight bulbs and rear tail/stop lights. The paint work is ok for 26 years old, its worse on the passengers side where a bungee cord rubbed on the rear wing before I fitted the windscreen and hood. Some small stone chips on the rear wing . Its got a crack in the paint on the scuttle passengers side. It also comes with a cover that goes from the rear of the car to the windscreen and a full cover. I've owned it for the past 4 1/2 years and have had some fun in it but the time has come to sell as i've done what I wanted to do with the european road trip with the wife. I also bought a Nissan 350z roadster last year so that has done most of the miles in the past 12 months. I'm looking for £5495 ono Contact me on here or slyv12@hotmail.co.uk

We've had a chat, me and Westmetal and we will get this finished in the spring . So, hands off it !!