Flying Carrot Steve Posted June 13, 2023 Share Posted June 13, 2023 1 hour ago, Kingster said: If you have the carbon lookee-likee pods as per Phil’s photo above and you have traditional Landrover lights (with filament bulbs) then in all likelihood the tub itself would have needed a bit of trimming for them to fit. I definitely have the carbon lookee-likee pods but no idea if they are Landrover lights, it's my first Westie so my knowledge of various bits isn't great. Yet. When you say the tub itself would have needed trimming, do you mean holes cut through the bodywork/rear arch for the wires or some other kind of trimming? Quote Link to comment Share on other sites More sharing options...
Kingster Posted June 13, 2023 Share Posted June 13, 2023 like this… because the light housings are big and long - led ones are slim Quote Link to comment Share on other sites More sharing options...
MR.C Posted June 13, 2023 Share Posted June 13, 2023 5 Quote Link to comment Share on other sites More sharing options...
Flying Carrot Steve Posted June 14, 2023 Share Posted June 14, 2023 15 hours ago, Kingster said: like this… because the light housings are big and long - led ones are slim Ok ta. I have holes behind but much smaller than those. Quote Link to comment Share on other sites More sharing options...
Kingster Posted June 14, 2023 Share Posted June 14, 2023 14 minutes ago, Flying Carrot Steve said: Ok ta. I have holes behind but much smaller than those. The original lamps are huge compared to leds 2 Quote Link to comment Share on other sites More sharing options...
AlanHodge Posted June 14, 2023 Share Posted June 14, 2023 17 hours ago, MR.C said: Ah miss my days and nights on the Lancaster Canal 1 Quote Link to comment Share on other sites More sharing options...
Phil B Posted June 17, 2023 Share Posted June 17, 2023 Todays job. Draw, print and install a slightly larger clutch pedal rest 3 Quote Link to comment Share on other sites More sharing options...
Flying Carrot Steve Posted June 17, 2023 Share Posted June 17, 2023 2 hours ago, Phil B said: Todays job. Draw, print and install a slightly larger clutch pedal rest Interesting. What material are you going to print it in? Am I right in thinking this attaches to the wall of the tunnel and sticks out as opposed to other ones I've seen like mine which is more like a recess cut into the tunnel wall? Quote Link to comment Share on other sites More sharing options...
Phil B Posted June 17, 2023 Share Posted June 17, 2023 Correct. Printed in PETG. I have the recess but find it just that bit too small so it’s to extend that. Riveted in place. But could also just be riveted to the tunnel for those that don’t have the wee pocket 1 Quote Link to comment Share on other sites More sharing options...
Flying Carrot Steve Posted June 17, 2023 Share Posted June 17, 2023 2 hours ago, Phil B said: Correct. Printed in PETG. I have the recess but find it just that bit too small so it’s to extend that. Riveted in place. But could also just be riveted to the tunnel for those that don’t have the wee pocket Excellent job! Any idea if it's possible to print a clear cover for my vernier cam pulleys? They would be great to look at but are covered by the usual black crackle finish cover. Quote Link to comment Share on other sites More sharing options...
Phil B Posted June 17, 2023 Share Posted June 17, 2023 1 hour ago, Flying Carrot Steve said: Excellent job! Any idea if it's possible to print a clear cover for my vernier cam pulleys? They would be great to look at but are covered by the usual black crackle finish cover. Doubt it. Only option for clear would be resin. And the thermal properties are really poor 1 Quote Link to comment Share on other sites More sharing options...
cjwood23 Posted July 14, 2023 Share Posted July 14, 2023 Spent a very very wet day at the Forest of Dean completing a British Cycling coaching award. I took 2 jackets and used them both - never been so wet lol 3 Quote Link to comment Share on other sites More sharing options...
Martin Bell - (Bellyboy) Joint East Anglia AO Posted July 15, 2023 Share Posted July 15, 2023 (edited) New shocks arrived thanks to Damperman.Progressive rear springs. Passenger side done above. 20mm rake after all were done. Will be getting them all tweaked and setup when theres some slots available. Everyones so busy. Pic of old ones after completing the job. Edited July 15, 2023 by Bellyboy Spelling 4 Quote Link to comment Share on other sites More sharing options...
corsechris Posted July 20, 2023 Share Posted July 20, 2023 Attempting to find an idle misfire fault on an old and pre-production CANEMS ECU...but without the car it belongs in. An Arduino providing the crank and cam signals, pots for MAP, WTS, TPS, IAT. The rather crude test rig worked fine, but sadly, absolutely no sign of the ECU misbehaving. In all likelihood it's something specific to the install, but the owner has already gone to pretty extensive lengths to eliminate all the usual suspects for an idle misfire. The car runs LPG & petrol, the petrol being supplied by the OEM and unmolested KE Jetronic, LPG by the CANEMS, so the issue has to be sparks, which the CANEMS supplies for both gas & petrol operation. Managed to make plenty of ozone but no sign of a problem. 6 Quote Link to comment Share on other sites More sharing options...
Ewan Posted July 22, 2023 Share Posted July 22, 2023 Chanced across a Westfield bonnet badge I bought a while back but decided not to fit. Then noticed it was the perfect size to replace the Momo badge in my steering wheel. Now looks way better. 6 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.