Weekend Warrior Posted July 5, 2017 Share Posted July 5, 2017 Whilst on overrun my handbrake light flickers and then stays on ,when accelerating away it goes off ,any ideas as to why? Steve Quote Link to comment Share on other sites More sharing options...
corsechris Posted July 5, 2017 Share Posted July 5, 2017 Is it also your low brake fluid warning light perhaps? Depending on the shape of the reservoir it could be low fluid causing that. 2 Quote Link to comment Share on other sites More sharing options...
Andrew Posted July 5, 2017 Share Posted July 5, 2017 Is it linked to the brake fluid level too? .. I think mine is.. 2 Quote Link to comment Share on other sites More sharing options...
Murraymint Posted July 5, 2017 Share Posted July 5, 2017 Yes as the guys say check the fluid or the 2 wires that run to the level sensor... 1 Quote Link to comment Share on other sites More sharing options...
Weekend Warrior Posted July 5, 2017 Author Share Posted July 5, 2017 Ok being a total non mechanically minded driver but learning every day ,if it's low I just top up pour in and put cap back on ,or wiggle wires and check connection ,simple as that . I will check tomorrow if low is all brake fluid the same . 1 Quote Link to comment Share on other sites More sharing options...
Thrustyjust Posted July 5, 2017 Share Posted July 5, 2017 Why is it low is the first thing to ask. Brakes worn ? Fluid leak ? Would check its none of those before putting more in. 1 Quote Link to comment Share on other sites More sharing options...
Weekend Warrior Posted July 5, 2017 Author Share Posted July 5, 2017 30 minutes ago, Thrustyjust said: Why is it low is the first thing to ask. Brakes worn ? Fluid leak ? Would check its none of those before putting more in. Ok fluid leak would be visible I guess so can check for that, discs are good almost new ,pads changed 3000 miles ago by previous owner,just had MOT they would have checked pads presumably ? Quote Link to comment Share on other sites More sharing options...
Thrustyjust Posted July 5, 2017 Share Posted July 5, 2017 Sensible to check rather than just putting some fluid in there and find out in an inopportune moment its all gone and you have no brakes. 2 Quote Link to comment Share on other sites More sharing options...
Thrustyjust Posted July 5, 2017 Share Posted July 5, 2017 23 minutes ago, Weekend Warrior said: Ok fluid leak would be visible I guess so can check for that, discs are good almost new ,pads changed 3000 miles ago by previous owner,just had MOT they would have checked pads presumably ? You would have been on the brake pedal all the time to wear the pads out in 3k miles. It maybe all fine and the previous owner changed the pads and retracted the caliper pistons and pushed the fluid out the master cylinder and then when the pedal was pressed to set the pads near the discs, it used a lot of the fluid in the reservoir. But it safety sake thing to double check its all sound at the fittings first. 1 Quote Link to comment Share on other sites More sharing options...
Matta Posted July 6, 2017 Share Posted July 6, 2017 I had something similar and it turned out to be a simple fix. Warning light was flickering at random, then a fuse blew. Turned out the metal bezel on the back of the light that holds it to the dash has unscrewed itself and was sitting across the 2 terminals, so had shorted out. Frustrating but straightforward once I found it. Matt Quote Link to comment Share on other sites More sharing options...
Quinten Posted July 6, 2017 Share Posted July 6, 2017 Check your handbrake switch as well. It will be underneath the gaiter. Quote Link to comment Share on other sites More sharing options...
Marcus Barlow - Show and Events Co-ordinator Posted July 6, 2017 Share Posted July 6, 2017 15 hours ago, Weekend Warrior said: Whilst on overrun my handbrake light flickers and then stays on ,when accelerating away it goes off ,any ideas as to why? Steve Are you sure its not the other red light which is the battery light as your symptoms would suggest alternator not charging battery Quote Link to comment Share on other sites More sharing options...
Andy_R Posted July 6, 2017 Share Posted July 6, 2017 I recently replaced my handbrake gaiter and there was a little extra material which I didn't trim away. This caused the gaiter & it's metal surround to raise slightly higher than before and it caused my light to go on and off likes yours is doing. Trimmed the extra material away and it's now back to it's correct position. Light is also back to normal. Quote Link to comment Share on other sites More sharing options...
Weekend Warrior Posted July 6, 2017 Author Share Posted July 6, 2017 Thank for all the helpful replies , found the brake fluid reservoir eventually had to follow brake pipes back ,whoever decided to tuck it away down in there wants a kick in the hole ! checked the wires to the lid all ok did an old contortionist trick ,eventually got the lid off and realised that there was indeed a float level sensor and that the fluid was near the bottom . not a hope in hell to see a max min level mark so put some in leaving it 3 cm or so from top . Believe it or not before I had the car and you helpful lot to ask I'd have probably taken it to the garage ,who no doubt would have checked through your list of answers until they found the fault and charged me a tidy sum for the privilege. Thanks again Steve Quote Link to comment Share on other sites More sharing options...
Ianboom Posted July 6, 2017 Share Posted July 6, 2017 Hi If you put your location on your profile, there may be somebody close to you who will come and check your brakes over and show you how to check them yourself. Well done for getting this far if you're pants a mechanics! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.