SteveB21 Posted November 14 Posted November 14 Point taken - but all I see is this, so no need to scroll through all the pictures again..! 2 Quote
Quinten Posted November 14 Posted November 14 1 hour ago, SteveB21 said: Point taken - but all I see is this, so no need to scroll through all the pictures again..! How odd, the browser used on my work laptop (Windows/Chrome) had them all expanded, but this browser (OSX/Chrome) does not. 🙈 I'll shut up and leave a little tip: you can highlight text in a post, and then a pop up will show 'Quote Selection', if you must absolutely quote... 1 Quote
Craigieboy Posted November 14 Posted November 14 6 hours ago, Benrobson2999 - Kent AO said: And bonnet holder which folds away when not in use Are you worried about it losing any shape whilst it's off, or have you braced it in any way? My FW bonnet splayed out a bit when it was off to do the radiator ducting. I got myself worked up a bit when I refitted mine and it wouldn't close properly, but then I remembered reading about how it was a common issue, especially at shows. It was fine after a couple of days and I'm sure the more experienced owners have all been through it 😁 3 Quote
John Ryan Posted November 16 Posted November 16 Finished fabricating a bonnet support for the X1. Boot strap, headlight and interior and done! 2 Quote
DeanMegaS2000 Posted November 16 Posted November 16 Sorned and stored, off on a work trip til Xmas 4 Quote
Eddie_R32 Posted November 17 Posted November 17 Cleaned the Westfield and decided to introduce it to my biggest car 6 Quote
Craigieboy Posted November 17 Posted November 17 9 minutes ago, Eddie_R32 said: Cleaned the Westfield and decided to introduce it to my biggest car Nice, just don't start the Pathfinder in gear! 3 Quote
Ansoeb Posted November 18 Posted November 18 New front grill made from ABS plastic. 285 grams lighter then the original, every little helps! 6 Quote
Benrobson2999 - Kent AO Posted November 18 Posted November 18 1 hour ago, Ansoeb said: New front grill made from ABS plastic. 285 grams lighter then the original, every little helps! That’s smart that how did you do the nice edge? Quote
Ian Kinder (Bagpuss) - Joint Peak District AO Posted November 18 Posted November 18 9 minutes ago, Benrobson2999 - Kent AO said: That’s smart that how did you do the nice edge? I agree the edge is nice, but won't be seen. Unless it's inserted into the nose, rather than flush behind the lip. Quote
Ansoeb Posted November 18 Posted November 18 1 hour ago, Benrobson2999 - Kent AO said: That’s smart that how did you do the nice edge. I used rubber edging strip. I think it's 7mm deep left over from another job. It definitely won't be seen but it gives it higher standard of finish. Just a geeky level attention to detail which floats my boat 2 2 Quote
tex Posted November 24 Posted November 24 My engine cover hangs on the wall. Fit x2 horizontal wooden bars to the wall. Drill x2 holes in the return lip of the engine cover 6in back from the front edge. Out of sight. Fit x2 wood screws in the top wooden batten that fit in the holes in the return lip. Hangs on the wall out of the way. Tip always place it no where near where you always walk past.. So you don't knock it off. Keeps it virtually dust free, stops it spreading wider and out the way. Quote
Naranja_Al Posted December 2 Posted December 2 Birthday present from the wife yesterday. I was even allowed the time to go and fit it! 7 Quote
Popular Post Kit Car Electronics and Essex AO Posted December 4 Popular Post Posted December 4 Took a voluntary redundancy/ early retirement deal so more time to play with cars and buttons (hopefully) 16 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.