RedditchJay Posted February 21, 2009 Share Posted February 21, 2009 Winter Project this year was Carbon rear lights and rear under valance..... Quote Link to comment Share on other sites More sharing options...
h4muf Posted February 21, 2009 Share Posted February 21, 2009 Just this minute got back from upgrade shop Removed spare wheel/carrier and gumins r500 clear back lights these New rear gaz shocks to match the front. Quote Link to comment Share on other sites More sharing options...
Bob Green Posted February 21, 2009 Share Posted February 21, 2009 Garrett GT3076R with External Wastgate and tubilar exhaust manifold. That would be special. My upgrade would to be drive more than 460 miles during 2008 (335 miles was one trip to Westbury) Poxy weather 1 Quote Link to comment Share on other sites More sharing options...
Gromit Posted February 21, 2009 Share Posted February 21, 2009 Alloy wheels. Lowered and uprated rear springs. Reset front torsion bars to lower front. New radio head unit, new amp for bulkhead mounted speakers and new dedicated power supply for audio. Sorted wiring out so phone can now run off radio. Sorted out the couple of rust blister on the bodywork. New interior lights (need me now). Added another storage rack. New bib spoiler under front bumper. Quote Link to comment Share on other sites More sharing options...
Pistol Pete Posted February 21, 2009 Share Posted February 21, 2009 Just got my MOT following conversion from x-flow to Vx 1.6 power, also survived rr session so I think I'm ready for the first sprint of the season next weekend . Pete Quote Link to comment Share on other sites More sharing options...
Boney Posted February 21, 2009 Share Posted February 21, 2009 Owdo 1) protech alloy shcocks 2) new momo wheel 3) LED rear lights 4) carbon fibre front splitter 5) intercom with new helmet (peltor headset built in) and peltor headsets yellow to match car 6) new cam and recorder to be installed with 2 way switch between old and new helmet cam 7) Fluke carbon fibre seats 8) finally get round to fitting carbon fibre front lights 9) new springs 10) spa speedo 11) got spa water temp and volt 12) new richbrook gaiters think thats it oh yeh get round to fitting it all instead of just taking space in spare bedroom maybe stack dash as well if other half doesn't notice and lose spa stuff:p regards Quote Link to comment Share on other sites More sharing options...
pembroke_pat Posted February 21, 2009 Share Posted February 21, 2009 New head going on to a 2 ltr zetec. Head now on bench Quote Link to comment Share on other sites More sharing options...
westy turbo Posted February 21, 2009 Share Posted February 21, 2009 Just got my MOT following conversion from x-flow to Vx 1.6 power, also survived rr session so I think I'm ready for the first sprint of the season next weekend . Pete Nice one!what did it made? Quote Link to comment Share on other sites More sharing options...
Matt Seabrook Posted February 21, 2009 Share Posted February 21, 2009 Photos of throbbing botties and 8 injectors Quote Link to comment Share on other sites More sharing options...
Matt Seabrook Posted February 21, 2009 Share Posted February 21, 2009 Carbon Dash Carbon aeroscreen New 200bhp+ XE Engine flooring Possible Wide track Rolling road. Geo set-up.. and about 8wks to do it.. Well pull your finger out then Quote Link to comment Share on other sites More sharing options...
BigDaveUK Posted February 21, 2009 Share Posted February 21, 2009 Done so far: Cage HT bolted on Buy slicks Fuel tank out and strengthen chassis in preparation for track and slicks! new quick rack in Buy trailer! Still To do.... Weld cage in Find some 13" CXRs for slicks Fuel Tank back in Replace brake light switch for one that works Swap bonnet locks for quick release catches Remove fog light and replace with LED flashing rain light. Suspension set-up Drive!!!!! Quote Link to comment Share on other sites More sharing options...
nikpro Posted February 22, 2009 Share Posted February 22, 2009 Photos of throbbing botties and 8 injectors Nice! Quote Link to comment Share on other sites More sharing options...
Arm Posted February 22, 2009 Share Posted February 22, 2009 Matt, where did you get the secondary fuel rail from ? Quote Link to comment Share on other sites More sharing options...
Matt Seabrook Posted February 22, 2009 Share Posted February 22, 2009 Morning Ash The fuel rail and injector mounts are from Jenvey. The injector mount is the RIH1 as seen in the photo below I just got Jenvey to make up a fuel rail with the correct spacing for the injectors Quote Link to comment Share on other sites More sharing options...
Arm Posted February 22, 2009 Share Posted February 22, 2009 Cheers Matt Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.