Jump to content

Crash damaged Narrow Body Breaking


Paul Ash

Recommended Posts

Ok all bits from 1990SE live axle in Radiant red.

I will always consider/accept reasonable offers only!

BITS STILL FOR SALE

4212.jpeg

1 x windscreen with polished Ali surround £50 (has a couple of small stone chips but has gone MOT's year after year without a problem)

1 x boot box (rac cut outs)    offers

1 x Nose cone c/w indicator pods and indicator lights (slight scratching but should polish out, will do it when got time) offers

1 x Scuttle  offers

Bonnett

1 x VX TB's cut out for air filter. offers

(cut out one has a stress crack on NS from accident but would be fine for a track car)

1 x chrome filler cap £10

1 x hood  (wont be available for a couple of months as blatters is borrowing it)

1 x dash panel Ali Vynil covered £5

Pedal box and cover (modified escort type) £20

1 x Std brake master cyl (from current Westfields) £50 REDUCED £40

OSF wishbones upper and lower + ball joints. £50 (will sell seperately if wanted)

Handbrake cable £5

1 x half shaft (english)

I,m sure there will be lots of other stuff as I strip it down.

Sensible offers only please. Via PM or e-mail so I can keep track of it all.

Heres some pics

4059.jpeg

4058.jpeg

4060.jpeg

4034.jpeg

4037.jpeg

4061.jpeg

BITS SOLD

4.1-1 diff (recently rebuilt by BGH) (english) £150 REDUCED TO £125   SOLD

RAC style Chrome roll bar - :D SOLD to Westy666

c/w hood hoops

2 x AVO shock absorbers for rear C/W springs (live axle.)

refurbed 2003. extra bump stop fitted so low ride height can be run and to stop diff flange hitting handbrake bracket, common problem on a early SE. :D SOLD to Westy666

Narrow Seats C/w Headrests black with red piping. (1 headrest needs attention as loose following crash, but not a big issue) c/w adjustable rails. :D SOLD :D

2 x willans 3 point harnesses in red

1  x windscreen infill strip  :D SOLD to Westy666

2 x rear lights

1 x rear fog light

1 x rear revers light

1 x cycle wing and bracket (suits 195 tyre et20 offset)

1 x full tonneau set i,e boot cover with rac key holes, half splitting tonneau seperate from boot cover, has slots just above doors so can run with side screens and still fix screens shut. made by Oxted Trim Co less than 2 yrs ago.

:D SOLD :D

1 x black carpet set (fair condition) drivers floor mat worn through. £50 :D Sold Barry Peel :D

Panhard rod and axle links £20 sold Tigger

Live axle drums,shoes,backplates (Spiral grooved0 recent cylinders / shoes) :D SOLD to Westy666

2 x 6" headlights in red FG holders Sold Boomy

1 new unused  bonnett £120 Sold

2 x side screens £100  SOLD

Link to comment
Share on other sites

Hi Paul I was thinking I might be interested in your boot box, (I am modding one at the mo but anything for an easy job), but your stays seem to be a lot further in than mine?? Is the boot box fit to the car in your picture?.

IMGP0092.jpg

Link to comment
Share on other sites

Yes boot box is in, in my car. Guess it will fit yours with some minor alteration. happy to sell it on a trial basis if that helps.
Link to comment
Share on other sites

The new nose cone and bonnet... hi or low line?... and how do I tell what mine are? (I'm guessing mine is low line)

thanks

MC :)

Link to comment
Share on other sites

1 x hood  (wont be available for a couple of months as blatters is borrowing it)

:blush:

As a thank you, I'll ship this to anywhere in the UK free of charge to whoever buys it, as long as they're a WSCC member.

Link to comment
Share on other sites

The new nose cone and bonnet... hi or low line?... and how do I tell what mine are? (I'm guessing mine is low line)

measuring from the front centre of the bonnet to line up with the base is just over 6inches for the lowline - high line is nearer 7.

FWIR you'd need a matching scuttle aswell if you were going from low to high  ;)

Link to comment
Share on other sites

Bonnett measurements

As removed and sitting on ground measured in centre of bonnett.

Back edge 10 1/2"

front edge 7 1/2"

Link to comment
Share on other sites

Hi Paul

How much do want for the side screens and have you got any photos of them?

Thanks

Kirk

Link to comment
Share on other sites

Quote  

The new nose cone and bonnet... hi or low line?... and how do I tell what mine are? (I'm guessing mine is low line)

measuring from the front centre of the bonnet to line up with the base is just over 6inches for the lowline - high line is nearer 7.

FWIR you'd need a matching scuttle aswell if you were going from low to high  

thanks... need to do some measuring :D

Link to comment
Share on other sites

Hopefully replied to everyone, If you havent had a response then PM me as Ive been a bit overwhelmed with e-mails pms etc so might of missed one.
Link to comment
Share on other sites

could i have the carpet set please

send pm I will post a cheque

Barry

Link to comment
Share on other sites

×
×
  • Create New...

Important Information

Please review our Terms of Use, Guidelines and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.