All Activity

Take them to Malvern where they can be given out to potential new members.

I have been a member of this great club since the end of 2010 and in that time have accumulated quite a few Westfield World magazines. It's now time for a clear out so I have 12 years of magazines from 2011 to 2022, and some calendars, for anyone who wants them, FOC. I would prefer collection if possible from Derby DE23 3WR, or I might be able to meet part way somewhere if my fuel costs are covered. Postage might also be possible, but I would need to work out packaging and costs. Thanks for looking, Steve.

Welcome from bonny we like photos, so dig into your wallet and become a full member , some great advice on here and good forum to follow.

Welcome @snakey22! As Stuart has pointed out, you need to be a full member to post photos. Membership is fantastic value and gives you access to loads of benefits, including; WSCC magazine, full access to all areas of the forum (including tech section, which given your intention to engine swap will be invaluable!), regular meet ups, as well as discounts on a range of products and services. Mat

Welcome to Wscc

@Ian Kinder (Bagpuss) - Joint Peak District AO Thankyou very much

I think I will be turning up, will be my first year and think it will prob be just one of the days not sure yet.

As we had a decent weekend weather wise finally managed to get out and fit some larger ignition leads from Burton along with some better matched spark plugs for the webers and finally managed to replace the old k&n filters with this one. Next on the list of to find a place to fit an oil catch can to the pipe that is just hanging down at the moment haha

Im also after one of these if anyone has one!!

New toys installed - ready for DIY painting…

Welcome

As an option I'm willing to split the parts: DanST manifold with silicone hoses and clips £275 (cost new from Danst £335) Nodiz ME Gen X pro with with loom ready to install £270 (cost new£330) Yamaha YZF R1 4XV (1998-2000) Carbs complete with Inlet filter and backing plate £195 All above as fitted to Zetec Silvertop 1.8 Collection from near Bingley, West Yorkshire or can post at cost.

@snakey22 welcome to the fold. I think you have to be a full member to upload photos though

Yorkshire area meeting this Tuesday, 3rd March at The Buffers, Rakehill Road, Scholes, LS15 4AL from 7:30ish. Unfortunately, I won't be there this month so I'll see you in April.

Hi, nice to hear about another early car. If you go to the bottom of the message box and hit the add files it should let you pick one from you phone assuming you are using one ! Where abouts are you ?

Awesome.. TY

Evening all just thought I would post as a new member, I’ve got a Westfield SE 1997 which I brought in 2021 had a Ford Crossflow when I brought it but am coming towards the end of a conversation to a Duratec. id upload pictures if I could work out how

Not bothered about condition so long as they are solid Thanks

Just a reminder that the Devon and Somerset meet is tomorrow at The Halfway House pub near Cullompton. Start at 19.30, normally finish by 21.30 ish.

Count me in. Driver and passenger please. Thanks for organising @Martyn Vann - Warwickshire AO In fact, that's my car on the far left of the photo you posted. It's a great way to spend a few hours

@tex hope this is helpful (edited to add that the maps below may not have uploaded in the right order so you may need to figure out which is which!) Day 1 1 Kendal to Old Dungeon Ghyll hotel 2 Old Dungeon Ghyll hotel to Kirkstile Inn 3 Kirkstile Inn to Kendal Day 2 4 Kendal to Hawes 5 Hawes to Malham 6 Malham to Kendal

Couple of simple jobs today, swapped the oh so time consuming to adjust belts to some nice Sabelt ones purchased second hand from a forum member… And swapped the ‘fried egg’ indicator bulbs for some silvered ones…

Cheers Ian, sadly at work but have some tinker time allocated later!

I might have to double up the skin then.. Much cheaper to make one. Simple 2x2 timber then staple each sheet from each side of the timber. That'd keep enough of a gap between the layers if pulled taught. Poly tunnel sheet is cheap and tough. Maybe a cheap dehumidifier could be help instead then..

Awesome! Is there a rough idea of the route so I have an idea?