All Activity

Please read the full listing !! FOR SALE SPARES OR REPAIRS ...... Westfield Sew 1997 The car is registered as a Westfield on the logbook This is a sew which means its a Widebody car running a live axle The car is running a 1700 Crossflow engine with a 5 speed type 9 gearbox 4 point belts mot until 2/10/2026 I have the v5c here It needs some tlc here and there There has been a small amount of damage that has been repaired on the drivers rear wing which if you want it mint will need some work Please view the pictures the car is hpi clear I checked this before i collected it This has to be the cheapest widebody on the market for sale . No offers I've priced it to sell . The car is for sale as Spares or Repairs !!!!!!! The car runs and drives I've collected the car drove it on to my trailer unloaded it taken the pictures that why its for sale as Spares or Repairs/ sold as seen The car is not taxed or insured so I cannot take you out for a test drive. if you are interested in the car turnup view the car take as long as you like looking at the car if you want to purchase it load it onto your trailer or truck and take it away. serious buyers contact me on 07523249617

Genuine Ford Blacktop Zetec / ST170 oil pump inc Billet gears. Removed from my car earlier this year. Billet gears (allow rpm to be raised, I ran to 7900rpm, others run these to 8500+rpm) supplied by Burton Power and fitted by Paul Exon in April ‘25 and have covered circa 500-600miles. £150.00 inc postage. Photos to follow.

The bubble I am using is great keeps everything nice and dry during the winter months, but yeah a bit of pain to turn off unzip right around the car then getting back in need to alight it up right so you can zip it all back up.. was looking for something a bit quick for the summer so did not have to worry about it.. but yeah that one you linked looks decent as well .

Raceline Zetec wet sump inc Blacktop/ST170 Windage tray. Starter motor on the exhaust side. Lower Raceline windage tray bolts all replaced by Paul Exon as part of engine rebuild in April 2025. Sump & finger plugs inc crush washers along with pickup top hat washers replaced at the end of 2025. Finger plug is drilled and tapped for an M12 x 1.5 sensor thread. £450.00 inc postage Photos to follow.

Spare QR boss and 5/8" weld-on shaft - this is the round boss with 6x70mm and 6x74mm PCD for steering wheels bolt holes - I used the boss for about 3 months before switching to a 3x50.8mm PCD steering wheel so there are fitting marks on the black boss but otherwise perfect and the shaft has never been used. Width: 85mm Depth: 90mm Weight: 0.34kg Shaft Diameter: BGR703: 5/8" New retail is £150, looking for £100 inc shipping or £95 collected (just south of Coventry or at a sprint etc by arrangement). Thanks Stuart .

I might get an indoor bubble for inside the tent for next winter when driving is at its minimum, but the drive in drive out facility of the tent as is is bliss. This comment is coming from previously just having a cover which couldn't easily be put on if the exhaust was hot.

I have one of these. It's just about big enough and is the biggest could fit in to my situation but a bit damp/condensaty in the winter. I could run a dehumidifier in the winter but the back 1/4 is on unsealed ground so I don't think it'd be much help. Or maybe just quite inefficient. https://www.houseoftents.co.uk/portable-garage/67835.html Very sturdy though, totally unaffected by the high winds these last two years, and there's enough room to work around the car as well, including lifting th engine out with a crane.

Im sorted now thanks. I found somewhere online that sells it by the metre. I didnt need a whole roll

As per the title, anyone in?

Hi all During the Winter months I use an In The Garage outside Car bubble to keep my Westfield nice and safe seems do be doing a great job so far. But wanted to change to something else for the summer as its a bit of a pain to keep getting in and out of the bubble.. Was thinking one of those folding car tents But wanted to see what everyone else uses.. well those people that don't have access to a proper garage anyway haha

Interesting; it does have one, (at least) significant red flag for me; it's got the notorious in-board front anti roll bar, commonly referred to as the chassis-breaker, round these parts. Fingers crossed the mileage is low enough it can be removed before damage occurs....

Yeh, very cheap for a Duratec car

As long as the weather is good I should hopefully make it up for Saturday.

I’ve been chasing an oil leak that I’d finally whittled down to either the rear main seal (RMS) or the gearbox input shaft seal. I decided to tackle the fix in my own garage for the first time. To make it work, I bought a new low-profile engine hoist that allowed me to drive the car over the legs; this meant I could push the car in and out of the garage to create the space I needed. I managed to get the engine out and back in within a day. Admittedly, the dry sump makes the job slightly more complex, but I bought some AN12 and AN10 caps so I could seal the pipework and pull the tank out while it was still full of oil. Once I pulled the flywheel to check the RMS, it actually looked perfectly dry. The front end of the gearbox, however, didn’t look quite so good!

Anyone fancy a drive out to Oulton Park Saturday, late am/early pm weather looks good. BMW track day, Coffee, chat, Ogle eachothers cars, mooch around the pit and paddock area. I'm planning being there from around 10:30 ish.

Open to offers in this….

@tex we all stayed there last year......

Are you able to confirm who the lucky folks are who have places ?

They've taken bookings and payment for the dates of this years tour too .

Happy birthday Martyn, hope Sue is treating you to plenty of cake, love from Glen and Julie xxxx

Sold

It was open last June, 2025.

I know it says Sep 2024..might be worth a check to see if it is still open..

Not as the title says lol. My car named will lol is going on for a warm up to our Meetup at 10am . Arbuckles downham market. May have food if people interested. Be nice to catch up. Thought the title would catch some interest

Went to Bedford today for trackday and the tab on the LH wing stay snapped off. Anyone willing to sell me one? I had to get creative with cable ties