Jump to content

Blogs

Restoration diary

Restoration Diary Day 1.

After owning my Westfield Sei with a crossflow engine for three years, and after spending a lot of time thinking, meditating, and stressing over whether I should restore it or upgrade it by swapping the crossflow engine for a Zetec or Sigma, I’ve finally decided to start by restoring and upgrading the chassis, body, interior, and other parts. I’ll also restore the crossflow engine and see if, with all these improvements, the car brings me enough satisfaction.   As the car stands today,
Fernando

Fernando in Restoration diary

1
SEiGHT

Discontinued...

After many years I've decided to abandon my blog and keep a build diary instead.   Follow my adventures here...  
Quinten

Quinten in SEiGHT

0
SEiGHT

February 2024

February 1st, 2024 Spend: £26.25   Using some 3D printed moulds (thanks to @Paul Aspden (MoFast) for releasing the STLs for his bonnet vents; they weren't a perfect fit, but it made designing these moulds a lot easier) I pressed my own bonnet vent meshes.            Have also given the meshes a quick once over with some paint as the original paint flaked off where it had bend the sharpest.     February 3rd, 2024 Spend: £0.00
Quinten

Quinten in SEiGHT

0
SEiGHT

January 2024

January 3rd, 2024 Spend: £16.60   Continuing with the side panel by bonding in the bonnet locating block       And then trial fitted it all when cured       January 14th, 2024 Spend: £48.00   Dreaded this moment a bit, but it's now time to fit some AeroCatches to replace the old bonnet locks.  Decided against the lower position which would have covered up the two holes left by the old lock, but would have also mean some
Quinten

Quinten in SEiGHT

0
SEiGHT

December 2023

December 16th, 2023 Spend: £0.00   Using the Enterprise Bold Italic font and Fusion 360, I created a copy of the Westfield badge that @Marcus Barlow - Show and Events Co-ordinator used to sell and printed it on my 3D printer (.STL attached).  Brass screw inserts sit on the back and then some thin aluminium was used to create tabs that hook into the back of the grille.     A few coats of primer followed by gold paint and lacquer makes it look convincingly metal
Quinten

Quinten in SEiGHT

0
SEiGHT

November 2023

November 4th, 2023 Spend: £5.00     Designed and 3D printed some tie wrap guides and bonded them in with P40.  This should hold the grille in place just nicely.         November 11th, 2023 Spend: £0.00       First layer of Isopon P38 applied and sanded       Last month: £  5341.94 This month: £     5.00             ----------+ Total:      £  5346.94
Quinten

Quinten in SEiGHT

0
SEiGHT

October 2023

October 1st, 2023 Spend: £0.00   Car is once again SORNed, it must be tinkering time...     October 18th, 2023 Sold: £50   Met up with @RickRack who bought my old 15" wheels.  Was great to catch up and am looking forward meeting his SEiGHT one day.     October 19th, 2023 Spend: £4.71   The nose cone on a SEiGHT is incredibly difficult to remove due to the cowling around the radiator, so to make life a little bit easier, I
Quinten

Quinten in SEiGHT

0
SEiGHT

May 2023

May 1st, 2023 Spend: £0.00     A lovely spring weather evening called for a spontaneous trip with my son and daughter.  Pulled over at Althorp estate and got few nice pictures.     May 11th, 2023 Spend: £270.00   After I replaced my front wishbones I knew I needed the wheel alignment checked and so I booked it in with Northampton Motorsport.  Was very surprised to learn that the car only weighs 680Kg.  I expected it to be a lot more given t
Quinten

Quinten in SEiGHT

0
SEiGHT

April 2023

April 8th, 2023 Spend: £514.07   A long time desire finally fulfilled.  13" Smoothies from John Brown Wheels.  5.5J for the front, 7J for the rear complete with Toyo R888Rs from Tyretek.       April 21st, 2023 Spend: £18.08   Finally gone all smoked lights by replacing the side repeaters by a smoked set from Performance Lights.         April 27th, 2023 Spend: £29.00     Arranged for a swap
Quinten

Quinten in SEiGHT

0
SEiGHT

March 2023

March 16th, 2023 Spend: £0.00   Continuing on the other side of the car with the spray on arch and arm protection        Took again multiple layers of black followed by a couple of layers of gloss FullDip to get good coverage       March 18th, 2023 Spend: £0.00        Sprayed the steering wheel boss black     March 22nd, 2023 Spend: £15.30   Installed new foam tape for the bonnet t
Quinten

Quinten in SEiGHT

4
SEiGHT

February 2023

February 4th, 2023 Spend: £10.00   So what to do with the gaping big hole left by moving the fuel filler?  Fill it up with a 3D printed blank and cover it with a V8 Westfield gel badge.       Big thanks to @Steve (sdh2903) who led the way with this and pointed me to someone who can create these gel badges in whatever colour/design you like.     February 5th, 2023 Spend: £0.00   I finally used the 3M Perfect It Gelcoat Medium Cuttin
Quinten

Quinten in SEiGHT

2
Onliest Music

Rock LEGO

I know there's a number of members who do LEGO...   Who would have thought LEGO did cover versions...  
Onliest Smeg David

Onliest Smeg David in Onliest Music

0
SEiGHT

January 2023

January 7th, 2023 Spend: £0.00        Having removed the rear arch protectors I need to fill the holes that are left behind and then I'm planning to use vinyl wrap to create new arch protectors, just like I did on my previous Westfield.  I'm using knifing putty to fill the holes and then sand it flat again using various grades of sanding paper.     Yes, it looks awful, but it's flat and the wrap will cover it all     January 15th, 2023
Quinten

Quinten in SEiGHT

0
SEiGHT

December 2022

December 4th, 2022 Spend: £108.56       On recommendation of Jody, I sourced an idle control valve / stepper motor which controls the idle by passing air into the plenum chamber upon startup but because my rocker covers where installed in such a way that the hose connecting to it would have to run the long way round, I went down the rabbit hole of swapping the rocker covers around.  This meant cleaning them, installing new gaskets, renewing filter, o-rings, plugs, leads,
Quinten

Quinten in SEiGHT

0
SEiGHT

November 2022

November 4th, 2022 Spend: £712.20   Collected the car from Jody and started to disassemble it again so I can give the new wishbones I kindly got from @Nemesis, and exhaust shields a lick of paint to further darken the car's appearance.         November 12th, 2022 Spend: £0.00        Multiple coats later...     November 16th, 2022 Spend: £221.51   With the wishbones finished, time to focus on fitting th
Quinten

Quinten in SEiGHT

0
SEiGHT

October 2022

October 1st, 2022 Spend: £35.90   Slowly going dark mode.         October 5th, 2022 Spend: £7.00       When I fitted the seats I used some black PVC edging, but this kept on coming off, so this time I've used some edging that has better grip.  Also went round the whole seat instead of just the sides.     October 14th, 2022 Spend: £0.00     An empty garage for a few weeks as Jody at J A Kit a
Quinten

Quinten in SEiGHT

0
SEiGHT

June 2022

June 18th, 2022 Spend: £54.04   For a while I was planning to replace my rear lights with something homebrew as I just can not find a nice aftermarket set that I like as much as I did on my previous Westfield.  Having already replaced my fog and reverse lights with those from the LED AutoLamps 82 Series, I thought maybe I should do the same for the indicators and stop/tail lights...?   The old units are quite wide, and these round lights are slightly taller than the spac
Quinten

Quinten in SEiGHT

1
SEiGHT

April 2022

April 9th, 2022 Spend £0.00   Having had @Nemesis SEiGHT in my garage for the past 2 months for an entire rewire job, I welcomed Barney back today.     April 17th, 2022 Spend: £0.00   After a lovely easter breakfast with the family, set off with Q-jr to meet up with Paul to drop off some tools that he'd forgotten to take home.  About a mile in, the engine shut off and we had to coast to a stop in a quiet road.  When turning the ignition the usual 2s f
Quinten

Quinten in SEiGHT

2
SEiGHT

January 2022

January 9th, 2022 Spend: £101.19     New year, time for action.  Having had a tiny coolant leak for ages it was time to sort it out.  But how the heck do you get the nose cone off when the radiator is part of it?  Turns out it relatively easy.  Just undo the top 3 screws on the duct and the 3 bolts holding the cone itself in place.  Access to the top 2 bolts was a challenge, but with the help of @Nemesis quickly sorted.     The number of joins is in
Quinten

Quinten in SEiGHT

0
Onliest Music

Bohemian Genre Bending

You'd have to head back all the way to August 2020 to find a light hearted fun musical blog of mine - music can be serious stuff! This band came up on my Spotify stream while working and thought some may be interested...   So it's time to head into frivolity with a Manc band I have seen several times at local gigs. Gypsies of Bohemia are masters of the cover version, serious re-writing of classics with great musicianship and humour in the presentation:   As the UKs
Onliest Smeg David

Onliest Smeg David in Onliest Music

0
SEiGHT

October 2021

October 1st, 2021 Spend: £8.25     Last week discovered to my great horror an oil spill on my drive the size of Exxon Valdez left after a drive.  After inspection it turned out to be squeezing oil past the oil pressure sensor, but even after tightening it, it still came dripping out.  Got some Permatex 59214 High Temperature thread sealant and re-assembled it all today.  So far it seems to have done the trick, but I need to take it on a trip (any excuse) first to ensure
Quinten

Quinten in SEiGHT

1
SEiGHT

September 2021

September 8th, 2021 Spend: £0.00     Company update required us to be back at the office (since over a year!) and when the weather is good, it would be rude not to take the Westie.     September 11th, 2021 Spend: £69.53   Took advantage of the Westfield Stoneleigh discount and bought new wiper arms to go with the taller windscreen.  I needed new blades anway.  Didn't realise I'd only been given one wiper arm when I collected it, but @Westfi
Quinten

Quinten in SEiGHT

0
SEiGHT

July 2021

July 9th, 2021 Spend: £0.00   First MOT in my ownership.  Given the all clear for another year       July 24th, 2021 Spend: £5.88     Used the 3D printer again to fabricate a phone holder.  Already had a .stl for the iPhone 8, and then designed a new clip that just slides between dash and scuttle.  Then fitted a USB charger so I can take it for a longer journey without worrying the phone nav runs out 😄     July 29t
Quinten

Quinten in SEiGHT

0

  • Blog Statistics

    56
    Total Blogs
    436
    Total Entries
×
×
  • Create New...

Important Information

Please review our Terms of Use, Guidelines and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.