Saltydog!! Posted November 9, 2004 Share Posted November 9, 2004 I offered my manifold up, in order to take some measurements for cutting hole in body later, only to find that one of the down pipes touches part of the block which sticks out. Has any one experienced this before? Can I just attack it with my grinder Any feed back appreciated. Ta muchly Quote Link to comment Share on other sites More sharing options...
Mark B Posted November 9, 2004 Share Posted November 9, 2004 Are you using the standard westfield manifold? It shouldn't really be anywhere near the block, mine certainly isn't, what part of the block does it hit? Mark. Quote Link to comment Share on other sites More sharing options...
thos Posted November 9, 2004 Share Posted November 9, 2004 I think some of the different Zetec versions uses a larger breather housing under the exhaust manifold. It was mentioned a few days ago. Quote Link to comment Share on other sites More sharing options...
Mark B Posted November 9, 2004 Share Posted November 9, 2004 Ah so probably not hitting the block itself more the breather "box" instead........ Quote Link to comment Share on other sites More sharing options...
Ted Posted November 9, 2004 Share Posted November 9, 2004 I am about to start building a Sport 1800, I asked Mark at Westfield about the positioning of the hole in the bodywork and he has sent me a diagram with measurements that suit the current exhaust manifold with the engine in its std position mated to the mt75 gearbox. I can't seem to post it here so if you would like a copy please pm me and I will send it to your email address. Sorry can't help with the fouling problem though as haven't got there yet. Regards TED Quote Link to comment Share on other sites More sharing options...
KerryS Posted November 9, 2004 Share Posted November 9, 2004 Ted You have PM Kerry S Quote Link to comment Share on other sites More sharing options...
Saltydog!! Posted November 9, 2004 Author Share Posted November 9, 2004 There is a piece of the block below the breather housing that sticks out towards the front of the engine, possibly a mounting for something. Anyway it is the std Westfield manifold and mine is meant to be the 'Madness' Zetec package (std 1800 with FI). I have a picture but how do I post it on here? I'll have to talk to the factory tomorrow - AGAIN!! Quote Link to comment Share on other sites More sharing options...
Saltydog!! Posted November 9, 2004 Author Share Posted November 9, 2004 Picture attached Any thoughts guys? Quote Link to comment Share on other sites More sharing options...
Saltydog!! Posted November 9, 2004 Author Share Posted November 9, 2004 If you're gonna have one... ...have a bigun!! Quote Link to comment Share on other sites More sharing options...
Blatman Posted November 9, 2004 Share Posted November 9, 2004 Jesus... I'd make that a bit smaller, just in case a dial upper is the chap with the answer, but no patience to wait for the picture to load... Quote Link to comment Share on other sites More sharing options...
Mark B Posted November 10, 2004 Share Posted November 10, 2004 Looks to me like the exhaust might be wrong, definitely give westfield a ring & tell them about it........ Quote Link to comment Share on other sites More sharing options...
Saltydog!! Posted November 10, 2004 Author Share Posted November 10, 2004 Dial up, what's that?? Quote Link to comment Share on other sites More sharing options...
Blatman Posted November 10, 2004 Share Posted November 10, 2004 Hey, I'm just trying to do my bit for those that live in the country... Quote Link to comment Share on other sites More sharing options...
perksy Posted November 10, 2004 Share Posted November 10, 2004 Saltydog Had a look at your picture and compared it to my Zetec install and there's something well wrong if the downpipe from your westfield manifold is hitting the cast part of the engine block Rough measured my clearance and it's around 60mm..... you do have the Westfield tubular stainless type Quote Link to comment Share on other sites More sharing options...
Saltydog!! Posted November 10, 2004 Author Share Posted November 10, 2004 As far as I know it's the standard Westfield fabricated 4 into 1 manifold/down pipe. I have sent a copy of the picture to Mark at WF to see what they make of it. I'll post an update once I know what the problem is. Looks like it's just me & my good fortune again!! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.