Jump to content

Leaderboard

  1. ACW

    ACW

    Administrator


    • Points

      2

    • Posts

      3,044


  2. Paul Aspden

    Paul Aspden

    WSCC Member


    • Points

      2

    • Posts

      982


  3. Dave Eastwood (Gadgetman) - Club Chairman

    Dave Eastwood (Gadgetman) - Club Chairman

    Administrator


    • Points

      1

    • Posts

      42,022


  4. pete g

    pete g

    Speed Series Competitor


    • Points

      1

    • Posts

      8,291


Popular Content

Showing content with the highest reputation on 19/02/14 in all areas

  1. Ok so onto the build up of the bottom end mounted on the engine stand. In this case I am using ARP main studs from SBD which are reusable compared to the OEM bolts. Because I will be using a dry sump pan that fits tight under the Main Bearing ladder I need to shorten the studs to prevent fouling as can be seen in the pic below. I do this by putting each on one the lathe and taking off around 4-5mm. Once this is done the studs are completed with the bench grinder followed by a thread file to clean them up. The studs are screwed in hand tight to the block using ARP Ultra Lube on the threads. This is after cleaning the fasters in brake cleaner and blowing out the holes in the block with the air line to make sure everything is clean and there is nothing to bind up. Once they are all fitted the main shells are pressed into place and lubed up on the bearing surfaces with assembly lube (the red stuff). I check that all the studs have gone in right using a straight edge against the block. Next the crank is cleaned up. In this case a steel Arrow SBD crank is been used. I liberally lube up the bearing surfaces with assembly lube. In this case I have already done a dry build with plastiguage to check clearances already. The crank is put into place and then after pressing the bearings into the main ladder this is placed onto the block studs. Take extra care to ensure nothing is on the mating faces between the block and the ladder. Washers and bolts are fitted with liberal amounts of arp ultra lube, again after cleaning the fasteners in brake cleaner. Next the main studs are tightended using a torque wrench. For these the technique is staring from the centre and working outwards to tighten initially to 25 lb-ft then to undo working out to in by 1/2 turn. Then back to 25 lb-ft starting centre to outside. Once this is complete they are done up to 60 lb-ft starting from centre to outside. Then undo 1/4 turn from outside back to centre. Then back up again to 60 lb-ft from centre to outside. This tighten / un-tighten sequence helps ensure that the main ladder is bedded to the block correctly and snug. As you tighten you should spin the crank around to make sure its sat nicely in the bearings. Next - Pistons and Rods.
    2 points
  2. Just a thumbs up for Troy at Northampton Motorsport, top bloke, managed to get the best from my car which covered more miles on his dyno yesterday than it has in competition to date! Hopefully Troy has managed to clean the floor of the dyno, & i promise to tighten the sump bolts before the next visit
    1 point
  3. Can't wait, as if there isn't enough competition Anyway,you should be running with the big dogs in H, I'm sure Barry will help tame the beast That will be the bellhousing bolts..... looking forward to an incident free season of sprinting, just a bit of prep work needed. Note to self, if you use very stiff engine mounts, prepare for stuff to shake loose!
    1 point
  4. I'm going into the Pretzel & popcorn business with Memb Sec. Were going to clean up :D
    1 point
  5. 1 point
  6. I can imagine that it might be tricky on the corners...
    1 point
  7. That's the end of Track days for us the punter, track day organisers and will have a serious detrimental financial effect on track owners. I sincerely hope that this is not the case and that the disclaimer we sign at track days stands up in the law of the courts. Insurance claims against third parties don't happen in motorsport, or not to my knowledge, so why should we be subject to it if we've knowingly signed a third party disclaimer on track days??? We need to be mindful of the fact that the incident last year was an insurance company trying to recover their costs from the third party, something that had never been done before and no doubt they were testing the waters within case law but fortunately they got their fingers burnt and withdrew the case. If they had taken all the way and been successful, the effect this would have had for all track day goers and operators world wide would have been devastating.
    1 point
×
×
  • Create New...

Important Information

Please review our Terms of Use, Guidelines and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.