All Activity

Might want to fix the title sir 👍

Set of 4 red leather diamond stitched fully reclining seats with harness slots sliding runners for front seats are included Seats are in very good condition Came out of a Landrover Defender One seat has a small blemish on the bolster (easy repair) These were specially made and of very high quality All seats have a reclining mechanism fitted (both sides) £1250. taking into account sliding seat runners are included, that’s less than £300 per seat!!

Brand new VW 349 aluminium radiator 580x380x38mm fits polo / lupo / seat arosa better cooling than the VW 302 due to larger surface area £25

Brand new VW 349 aluminium radiator 580x380x38mm fits polo / lupo / seat arosa better cooling than the VW 302 due to larger surface area £25

Reduced to £25 Got to be a bargain at this price!

Brand new VW 349 aluminium radiator 580x380x38mm fits polo / lupo / seat arosa better cooling than the VW 302 due to larger surface area £25

Yep use them all the time; but also found them nearly impossible to drive onto without at least pushing them out of place, and sometimes one would slide further than the other! So I've long since given up driving on and now just lift the car on to them with a trolley jack. As for safety, I've seen axle stands start to topple too, if too much lifting (bad) or sideways forces are applied to the car. (Though I'll always try and make sure high torque items where possible are at least cracked loose while the cars tyres are on the ground, even if some load is being taken on a jack. If I've got both ends of the car raised and one or More wheels off, I'll also put the removed wheel(s) under, or part under the car near where I'm working as a backup; in the insanely unlikely event of it falling off the stands, even if I'm pinned, it will be the wheels taking the bulk of the cars weight, not me!

Still looking

Have a pair of these and find they give you the hight to get a trolly jack underneath and then use axle stands.

I've thought about something like this as I've got a converluted system of home made ramps and blocks to get the car high enough to get the ramps under. It wouldn't pass any health and safety tests.

Hi All, Please can someone recommend an external rain storage cover, a supplier. Preferably one of a heavier material and either elasticated or held with straps under the body. I can see websites advertising covers for all manufactirers of vehicle, but suspect they may not be very custom for the Westfield. Thanks in advance. Mark.

if find those ramps tricky or don’t like them. I pull my car onto these low profile ramps so front car is higher. so i can then Jack it up as front of my car is too low for the low profile Jack to go under without hitting nose cone or side of the car. Then I use axle stands for it. But I still get decent high to change oil or mess around cleaning. But if want more hight/room those ramps or axle stand will be best.

I've honestly never had a problem just driving up onto my ramps and getting on with stuff.

Could you cut the sleepers in half and turn them round?

Fancy!

Ditto- I'd be happier if the sleepers were a tad wider 🤦‍♂️

I tried an old pair that were given to me, impossible to drive onto them as they kept being pushed away due to the light weight of the car a wide tyres. I have a 2 pairs of axle stands with a square section bar welded between them and thin carpet stuck to the bar, works great

I put an end stop on one end of the 4*2 and two stops on the rear face and a magnet either end sunk in the top face which allows me to slide the wood under and click it in place which makes it much easy we and less times up and down on and off my knees!

I jack the front up and put the ramps under and jack the back for the axle stands. Be careful letting it down, as mine rolled off the ramp when I turned my back.

That's what I do at the moment, @Mole. I probably just need to get better at it.

I do exactly the same. The 4ft length of 4x2 spreads the load nicely. Axle stands and trolley jack to support middle and either end are excellent.

I put the axle stands under the rear cross member behind the seats, well actually as I have got dropped floors I have a length of 4*2 that I put across and jack in the centre of it and then the axle stands go under that at full width I do similar at the front. The axle stands are then well spread out. There is no rock or movement if I try to wobble the car. I feel that it is solid and safe.

NTDWM… https://classifieds.seloc.org/ads/westfield-seats/

I have some with a built in bottle jack and they are fantastic. Drive onto them almost flat then jack them up. Locking mechanism when jacked + use axle stands too

Thanks for the thoughts all. I've a low profile jack already and some totally adequate stands. Maybe I should just play with the rear placement a bit.